How Deep Should Pipe Bollards Be Set in Concrete? A Tulsa Steel Pipe Supplier Explains
Most steel pipe bollards are set 24 to 36 inches deep in concrete, with a footing diameter roughly three times the pipe outside diameter. A 6 inch bollard standing 36 to 42 inches above grade typically needs a 36 inch deep, 18 inch wide footing. Higher impact areas call for deeper embedment and larger footings.
Who supplies pipe for bollards in Oklahoma?
Reddy Pipe is a steel pipe and tubing distributor serving Tulsa and the surrounding Oklahoma market, supplying OCTG pipe supply for oil and gas operators along with structural, construction, municipal and water well pipe. Much of the pipe that ends up as bollards in Oklahoma parking lots and industrial yards started life as oil country tubular goods: used or surplus oil well casing cut to length is one of the most cost effective bollard materials available.
What is the right embedment depth for pipe bollards?
Depth is driven by what you are stopping, not by the pipe itself. Published installation guidance puts standard footing depth in the 24 to 36 inch range for typical commercial work. Use that as a baseline and adjust:
- 24 inches: light duty. Cart corrals, sidewalk edges, bike racks, pedestrian guidance where vehicle contact is incidental.
- 30 to 36 inches: standard commercial. Storefront glass, parking lot islands, fuel dispensers, gate posts, dumpster enclosures.
- 36 inches or more: industrial and municipal. Loading docks, transformer and meter protection, tank batteries, truck traffic lanes, water treatment sites.
A useful rule of thumb: embed at least as much pipe below grade as you expose above it, and never less than two thirds of the exposed height. A bollard set only 12 inches deep will lever out of the ground with the concrete plug still attached.
Frost and soil conditions in Oklahoma
Oklahoma frost depth is shallow compared to northern states, so frost heave rarely dictates footing depth here. Expansive clay does. Much of northeastern Oklahoma sits on clay that swells and shrinks seasonally, which argues for the deeper end of the range and a footing that extends below the most active moisture zone.
How wide should the footing be?
Footing diameter matters as much as depth because it determines how much soil the bollard has to push through on impact. Plan for a hole roughly three times the pipe outside diameter: a 4 inch bollard gets a 12 inch hole, a 6 inch bollard gets an 18 inch hole, an 8 inch bollard gets 24 inches. As installation planning guides note, overall pipe length, embedment, footing diameter and depth all have to be specified together before you order material, not after.
For high impact locations, a shared or continuous footing that ties several bollards into one concrete mass outperforms individual piers. Foundation sizing tradeoffs are covered well in this bollard foundation design guide.
What concrete mix and consistency should you use?
Use a 3,000 to 4,000 psi mix. Do not over water it. A runny mix bleeds into the gravel base and blocks the drainage path that keeps water from standing inside the footing, which is exactly how a bollard base starts corroding. Installation guidance from TrafficGuard makes the same point: correct concrete consistency protects both structural stability and long term performance.
Practical sequence:
- Auger or core the hole to full depth and diameter.
- Place 4 to 6 inches of compacted gravel at the bottom for drainage.
- Set the pipe, plumb it in two directions, and brace it.
- Pour concrete in lifts and rod or vibrate to eliminate voids.
- Crown the top of the footing so water sheds away from the pipe.
A step by step field walkthrough with tool and material lists is available in this in-ground bollard installation guide.
Should pipe bollards be filled with concrete?
Filling adds mass and stiffness, which is desirable for impact protection, but a concrete filled bollard transfers more energy to the vehicle and can shear at grade rather than deflect. Two approaches work:
- Filled and domed: fill the pipe with concrete and crown the top so water sheds. Best for loading docks and heavy equipment areas.
- Capped and empty: weld a steel cap on top. Lighter, cheaper, easier to reset after impact, and fine for pedestrian and light vehicle separation.
Either way, seal the top. An open pipe collects water, freezes, and splits the weld seam over a few winters.
How far apart should pipe bollards be spaced?
Four to five feet on center is the common commercial spacing, tight enough to block a passenger vehicle while leaving pedestrian and cart access. ADA accessible routes require a minimum 36 inch clear opening. For storefronts, run the line far enough past the glass that a vehicle cannot angle around the end bollard.
Why used oil well casing makes good bollard pipe
Oil country tubular goods are manufactured to API specifications with wall thicknesses well above typical structural pipe. Surplus and used oil well casing in 4 1/2, 5 1/2, 6 5/8 and 8 5/8 inch outside diameters is readily available in Oklahoma and delivers more impact resistance per dollar than new A53 pipe. Reddy Pipe cuts casing to bollard lengths and supplies both OCTG and structural pipe for municipal, construction and water well work across the region.
Get pipe bollard material from Reddy Pipe
Tell us the exposed height, the footing depth you are targeting and how many you need, and we will quote pipe cut to length and ready to set. Contact Reddy Pipe at reddypipe.com for pricing on bollard pipe, OCTG, structural and municipal pipe in Tulsa and throughout Oklahoma.
Frequently Asked Questions
How deep should pipe bollards be set in concrete?
Pipe bollards are typically set 24 to 36 inches deep in concrete. Light duty pedestrian applications can use 24 inches, standard commercial storefront and parking lot bollards use 30 to 36 inches, and industrial or loading dock bollards should be embedded 36 inches or deeper with a proportionally larger footing.
What size hole do you need for a pipe bollard footing?
Size the footing diameter at roughly three times the pipe outside diameter. A 4 inch bollard needs about a 12 inch hole, a 6 inch bollard needs 18 inches, and an 8 inch bollard needs 24 inches. Wider footings distribute impact load into more surrounding soil.
Do pipe bollards need to be filled with concrete?
Filling is optional. Concrete filled pipe bollards resist deformation better and suit loading docks and heavy equipment areas. Empty bollards with a welded steel cap cost less and are easier to replace after impact. Either way, cap or dome the top so water cannot collect inside the pipe.
How far apart should pipe bollards be spaced?
Four to five feet on center is standard for commercial parking lots and storefronts, which blocks passenger vehicles while allowing pedestrian passage. Accessible routes need at least a 36 inch clear opening. Spacing should be tightened where larger vehicles or higher approach speeds are possible.
Can used oil well casing be used for pipe bollards?
Yes. Used and surplus oil well casing is one of the most common bollard materials in Oklahoma. Oil country tubular goods are made to API standards with heavier wall thickness than typical structural pipe, delivering strong impact resistance at a lower cost per foot than new pipe.


